XENON Ultrahigh Quartz Pressure Mercury Light Bulb UV 250W USSR DRSH 250-3

Description

XENON Ultrahigh Pressure Mercury Light Bulb UV 250W Lomo-Zeiss
USSR DRSH
250-3
Spherical mercury-quartz lamps of ultrahigh pressure like DRSh are the powerful, concentrated radiation sources in visible and ultra-violet parts of a range.
Lamps intend for use in optical devices and for laboratory researches.
Line voltage -
220V
Lamp current -
4.0A
Lamp voltage -
93V
Lamp power -
250W
Ultrahigh-pressure ball mercury-quartz lamps of the DRSh type are powerful, concentrated radiation sources in the visible and ultraviolet parts of the spectrum.
Ultrahigh-pressure mercury lamps with a ball bulb type DRSh 250-3 are intended for use in optical instruments and for laboratory research when powered through special inclusions (lamp power supply DRSh-250-3, remote control PRL-5 and others like that) from an alternating current main with a frequency 50 Hz.
They are used in luminescent microscopes: MLD-1, ML-2, LUMAM R-8 and others.
The lamp of the DRSh 250-3 type is designed to operate on alternating current with a voltage of 127 in series with chokes. During the first 10-15 minutes. after the lamp is turned on, its electrical parameters change (transient mode), and then remain constant (steady state) with a constant voltage.
The DRSh 250-3 lamp is a spherical quartz glass flask into which two diametrically opposite electrodes are sealed at a distance of 3.9-4.5 mm. To facilitate ignition of the lamp, the 3rd ignition electrode is soldered into the ball on the side. The lamp is dosed with a strictly defined amount of mercury and argon. Arc discharge occurs in mercury vapor, generating high brightness.
A schematic diagram of the inclusion of a lamp in an AC network is shown in the figure below.
drsch-250-3 rice 2
D - throttle
L - lamp
K - push button switch
And - an inductor for ignition with a spark length of 15-20 mm
С-1 - capacitor for suppressing radio noise of a lamp with a capacity of 0.05 microfarads at an operating voltage of at least 250 V.
С-2 С-3 - blocking capacitors to limit radio interference of a network with a capacity of 0.5 μF to an operating voltage of at least 250 V
The lamp is ignited using an inductor with a spark length of 15-20 mm, which is switched on with the K button for a short time (no more than 1 min). After the occurrence of an arc discharge between current-carrying electrodes, the inductor is turned off. The wire from the inductor is connected to the base of the ignition electrode.
The normal operating position is vertical, the ignition electrode is on top (the maximum permissible deviation from the vertical position is 10 °). Normal ignition and lamp burning occurs at an ambient temperature of at least + 15 ° C and a voltage of at least 115 V.
Rated power, W - 250
The voltage on the lamp is nominal, in - 72
Rated lamp current, A - 4
Luminous flux not less than lm - 10000
Brightness not less, mnt - 100
Ignition voltage no more, in - 115
Choke voltage:
in starting mode, at - 127
in operating mode, in - 93
Amperage:
in starting mode: 6.5 - 8 A
in operating mode: 3.8 - 4.2 A
Burning duration not less than h - 300
The average value of the luminous flux and brightness after the average duration of combustion should be at least 80% of their limiting values.
Lamp length no more, mm - 145
The diameter of the flask, mm - 26.5
Lamp height, mm - 40
Lamp weight, g - 27
PRECAUTIONARY MEASURES
The valve body must be earthed and the electrical connections must ensure reliable contact.
The lamp is attached to the legs or socles of the conductive electrodes.
The lamp can operate in a limited volume (casing) provided that the casing dimensions and ventilation conditions are such that the air temperature at a distance of 6 cm from the walls does not exceed 250 C (in steady state). To re-ignite the lamp after it is turned off, it takes no more than (less) 6 minutes.
The ambient temperature should be between 15 and 45 ° C, and the relative humidity should not exceed 70%. Forced cooling in the process of lamp burning is not allowed.
Quartz glass of a bulb of a lamp easily loses its transparency when its surface is contaminated. In view of this, if the flask is contaminated (for example, after touching it with hands, dust on it, etc.), it is necessary to wipe the flask with cotton moistened with alcohol before switching it on.
Personnel working near the lamps and nearby equipment and combustible substances must be protected from hot splinters of the lamp bulb in case of explosion.
When using the lamp, measures must be taken to protect personnel from the effects of powerful ultraviolet radiation from the lamp. In the event of a lamp fight, collect mercury with a rubber bulb and rinse the place where the lamp crashed, rinse with a 1% solution of potassium permanganate. Lamps that fail should be taken out of town and buried in the ground.
Like most gas discharge lamps, DRSh 250-3 lamps, in the absence of appropriate protective devices, can be a source of radio interference. To limit radio interference in the network into which the lamp is switched on, the network blocking should be applied using capacitors with a capacity of 0.5 microfarads.
Lamps like DRSh are intended for work on alternating current with tension 127v for lamps of DRSh 250—3 and 220v for lamps of DRSh of 500 M and DRSh 1000 is consecutive with throttles. Within the first 10 — 15 min. after inclusion of a lamp, its electric parameters change (the unsteady mode), and then remain constants (the set mode) at an invariable tension of a network.
Lot for 1 pc
Payment
1. We accept PayPal only.
2. All major credit cards are accepted through secure payment processor PayPal.
3. Payment must be received within 5 business days of auction closing.
4. If you have bought multiple items from me, you can send me one payment for all the items instead of paying for them individually. When you click the Pay Now button, eBay will automatically determine if there are other items you have won or purchased from me and will combine them for your review.
NOTE:
Import duties, taxes and chargers are not included in the item price or shipping charges. These charges are the buyer's responsibility.
Please check with your country's customs office to determine what these additional costs will be prior to bidding buying.
Shipping
1. We ship Worldwide.
2. Items will be usually shipped within 2 business days on payment received.
3. We use UkrPoshta (Ukranian Post) for our International  deliveries. Once your package passes through customs it will be delivered by your local post office.
4. The usual time for a parcel to arrive at its address is 24 business  days, but usually it arrives much earlier. Sometimes it can take longer up to 8 weeks.
5. We can send to USA by UPS (3-4
business days delivery
) - 1.1lbs, - 2.2lbs, - 3.3lbs, - 4.4lbs, - 6.6lbs
Delivery time lasts approx.
1) United States 12-24 business days.
2) Europe: up to 21-24 (except Germany and Italy, delivery time can take up to 1 month)
3) Other countries: not more than 30 business days.
4) Canada & Asia & Australia: the delivery can take up to 2 months, but  usually it arrives much earlier.
We appreciate your patience if you haven't received items in 30  days may need more patience by reason of the local delivery system  and/or customs. If you are concerned in any way, please feel free to  contact us via ebay message instead of leaving negative/neutral  feedback or opening a dispute. We will make every effort to fix any problem.
Returns
We guarantee you complete satisfaction with all our high quality products.
If you receive an item you did not order, or if an item you ordered is received damaged or defective, we will refund you the price you paid for it or replace it with identical one.
The item should come to the above address within 30 days after you received it.
After 30 days we will no longer be responsible and the item won't be taken back.
Item for returning must have the original tags and packing, otherwise it won't be accepted.